實驗室小容量水浴恒溫振蕩器使用方法

1、在水箱內加入適量的水(水位高度以超過彈簧夾具2-75px為宜)，將試劑瓶裝在彈簧夾上。
2、先接通電源，打開加熱開關，溫控儀亮，此時點擊溫控儀上的SET功能鍵，此時點擊溫控儀上的set功能鍵，上排顯示sp，下排顯示設定溫度，點擊△或▽鍵選擇所需工作的溫度，設定完畢再次點擊set功能鍵進入恒溫定時設定，上排顯示st，下排顯示設定時間，點擊▲或▼鍵選擇恒溫定時時間，(若無需定時，將時間設定為0即可)再次點擊set鍵退出設定狀態。此時箱體內的溫度即按設定溫度恒溫運行;運行完畢蜂鳴器報警提示并停止加熱。
3、調節振蕩“定時旋鈕"，選擇振蕩定時時間(如無需定時，將定時旋鈕調至在常開位置即可)，然后緩慢調節“調速旋鈕"，調至所需振蕩速度。
4、使用完畢，將調速旋鈕調至0位，關閉電源，若長時間不用，請拔下電源，將水放凈，及時清理并擦拭干凈，以延長使用壽命。